1. Structural Architecture & Physical Geometry
This matrix defines the exact dimensional engineering, physical profile, and material composition of the C210-018 blade component.
| Technical Parameter |
Specification & Engineering Detail |
| Product Line Series |
OSS Team C210 Series High-Precision Modules |
| Model Number Code |
C210-018 (Integrated Knife / Blade Profile) |
| Tip Profile Geometry |
45° Beveled Knife Edge with a micro-thin flat working face |
| Blade Surface Thickness |
~1.5mm gradient tapering to a micro-edge |
| Internal Core Chemistry |
Oxygen-free high-conductivity (OFHC) pure copper |
| Structural Plating Layers |
Layered Iron-plating (anti-wear) backed by Chromium coating (anti-corrosion) |
| Tip Face Finish |
Factory pre-tinned lead-free alloy coating |
| Total Assembly Length |
Standardized 80mm inline form factor |
| Net Operational Weight |
Approximately 4.5g to 5.0g |
2. Thermal Capabilities & Electrical Parameters
This table details the energy distribution, efficiency metrics, and internal tracking electronics embedded within the tip.
| Performance Attribute |
Metric Threshold & Behavior |
| Rated Power Handling |
Optimized for stations scaling up to 45W - 75WÂ burst outputs |
| Heating Integration |
3-in-1 Design (Heating element, thermocouple, and tip face are a single unit) |
| Thermal Recovery Cycle |
Immediate loop correction (~1.5 seconds to return to setpoint) |
| Cold Startup Latency |
Reaches standard working melting point (350°C) in 2 seconds
|
| Operational Window |
Stable operations across 100°C - 450°C range |
| Internal Sensor Array |
Integrated internal K-Type Thermocouple feedback circuit |
| Insulation Resistance |
>100M omega at standard environmental thresholds |
3. Application Use-Cases & Rework Suitability
This matrix breaks down the exact micro-soldering tasks where the C210-018 knife tip excels on modern circuitry.
| Target Application Area |
Technical Suitability & Rework Performance |
| IC Pad Drag Soldering |
The flat edge of the blade cleans away residual solder from BGA footprints in a single pass without scratching the solder mask. |
| Micro-Jumper Wire Work |
The sharp corner point (0.18mm effective radius) makes it easy to solder jumper wires directly to tiny component traces under a microscope. |
| FPC Flex Cable Bonding |
Delivers even, linear heat across multi-pin row connectors, ensuring uniform joints for display or charging flex cables. |
| Underfill & Glue Removal |
Safe to use alongside hot air to slice through tough black glue, epoxy resins, and UV structural adhesives around processors. |
| SMD Multi-Pin Rework |
Simultaneously heats arrays of passive components or small outline IC pins (SOIC/TSOP) for rapid, damage-free removal. |
4. Compatibility, Protection, & Lifecycle Maintenance
This data matrix highlights cross-system compatibility, environmental handling protocols, and care routines to extend tip life.
| Lifecycle Category |
Protocol Rules & Technical Design Features |
| Handle Cross-Compatibility |
Native fitment for OSS Team T210, JBC T210, Sugon T210, and Aixun T210 precision iron handles. |
| Static Control Compliance |
Full ESD-Safe validation; directly grounded through the internal handle interface to eliminate voltage leaks. |
| Oxidation Protection |
Advanced plating prevents alloy degradation when running lead-free processes (380°C- 420°C). |
| Best Cleaning Practices |
Use high-density brass wire mesh or specialized tip tinner compounds; do not use file blocks or wet sponges. |
| Idle Standby Care |
System firmware automatically cuts power when the tool is docked, preventing chrome layer blistering. |
Summary of Core Advantages
-
Zero Heat Transfer Loss: Because the heating element is sealed inside the tip core, there is no thermal drop-off. Heat transfers instantly to the board without overheating nearby micro-components.
-
Dual-Use Tip Geometry: The long side edge handles large area cleaning and drag-soldering, while the sharp tip point easily manages fine micro-jumper work.
-
Toolless Plug-and-Play Swaps: Can be pulled out and swapped directly on the station cradle while hot, removing the need for cooling downtime or specialized wrench tools.
Â
Â
Â
Mobile
Repairing Tools
Touch/Glass/OCA
Glass
Stencils &
IC
OCA Machine &
Parts
Mobile
Accessories
Software
OCA
Sheets &
Polarizers
Customer Reviews
No reviews yet
Be the first to review this product.